AMX NXI Specifikace

Operation/Reference GuideCentral ControllersNXINetLinx® Integrated Controller(No Master)Last Revised: 5/31/2012

NXI NetLinx Integrated Controller4NXI NetLinx Integrated Controller (No Master)

Connections and Wiring5NXI NetLinx Integrated Controller (No Master)Connections and WiringInstalling the Master or Hub CardThe NXC-ME260 NetLinx Maste

Connections and Wiring6NXI NetLinx Integrated Controller (No Master)IR/Serial Connections and WiringYou can connect up to eight IR- or serial-controll

Programming7NXI NetLinx Integrated Controller (No Master)ProgrammingThis section describes the Send_Commands, Send_Strings, and Channel commands you c

Programming8NXI NetLinx Integrated Controller (No Master)Program Port CommandsCommand DescriptionDATE Displays the current date and day of the week.DE

Programming9NXI NetLinx Integrated Controller (No Master)Program Port Commands (Cont.)SET DATE Prompts you to enter the new date for the Master Card.W

Programming10NXI NetLinx Integrated Controller (No Master)ESC Pass CodesThere are 'escape' codes in the pass mode. These codes can switch th

Programming11NXI NetLinx Integrated Controller (No Master)LED Disable/Enable Send_CommandsThe following commands enable or disable the LEDs on the NXI

Programming12NXI NetLinx Integrated Controller (No Master)RS-232/422/485 Send_Commands (Cont.)CHARDM Sets the delay time between transmitted character

Programming13NXI NetLinx Integrated Controller (No Master)RS-232/422/485 Send_Commands (Cont.)HSON Enables RTS (ready-to-send) and CTS (clear-to-send)

AMX Limited Warranty and DisclaimerThis Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Part

Programming14NXI NetLinx Integrated Controller (No Master)RS-232/422/485 Send_String Escape SequencesRS-232/422/485 Send_String Escape Sequences27,17,

Programming15NXI NetLinx Integrated Controller (No Master)IR / Serial Ports (8 - 15) ChannelsIR/Serial Send_CommandsThe following IR and IR/Serial Sen

Programming16NXI NetLinx Integrated Controller (No Master)IR/Serial Send_Commands (Cont.)CTOF Sets the duration of off time (no signal) between IR pul

Programming17NXI NetLinx Integrated Controller (No Master)IR/Serial Send_Commands (Cont.)POF Turns off a device, based on input Link.• If at any time

Programming18NXI NetLinx Integrated Controller (No Master)IR/Serial Send_Commands (Cont.)SET IO LINK Links an IR or Serial port to an I/O channel for

Programming19NXI NetLinx Integrated Controller (No Master)IR/Serial Send_Commands (Cont.)XCHM Changes the IR output pattern for the XCH command.Syntax

Programming20NXI NetLinx Integrated Controller (No Master)Input/Output Send_CommandsThe following Send_Commands program the I/O ports on the NXI.IR/Se

Programming21NXI NetLinx Integrated Controller (No Master)

6/12 ©2012 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without not

Table of ContentsiNXI NetLinx Integrated Controller (No Master)Table of ContentsNXI NetLinx Integrated Controller ...

ii NXI NetLinx Integrated Controller (No Master)Table of ContentsSHOW REMOTE ...

Table of ContentsiiiNXI NetLinx Integrated Controller (No Master)CTOF ...

iv NXI NetLinx Integrated Controller (No Master)Table of Contents

NXI NetLinx Integrated Controller1NXI NetLinx Integrated Controller (No Master)NXI NetLinx Integrated ControllerOverviewThe NXI NetLinx Integrated Con

NXI NetLinx Integrated Controller2NXI NetLinx Integrated Controller (No Master)SpecificationsNXI SpecificationsPower requirements 1.09 A @ 12 VDC (NXI

NXI NetLinx Integrated Controller3NXI NetLinx Integrated Controller (No Master)NXI Specifications (Cont.)Rear Panel Components (Cont.)Relay port (Port